Referentie: 45511 B1
Upright rear L/R
Splin-Drive upright for the rear of the TRAXX .and fourtex
Fits both left and right side.
Including bearings
Op voorraad
- Er zijn geen items meer in uw wagen
- Verzending
- Totaal € 0,00
- 1:10 Scale
- 1:6 Scale
- 1:8 Scale
- BBB-P Shocks
- Downloads
- Electronics
- Materials
- Silicone Oil
- Tools
Bushing with conical collar (Ø3mm/Ø4mm)
Waardering
Bushing with conical collar for the servo saver.
Inside Ø3mm
Outside Ø4mm
Fits ball joint (50320-20) which has a hole of Ø4mm
Omschrijving
50445-06
Productdetails
50445-06 B2
14 Items
Recensies
Geen klantenbeoordelingen op het moment.
16 andere producten in dezelfde categorie:
Referentie: 50320-40-r
Piston rod (rolled M5 ending)
Piston rod / shock shaft with thread rolled M5 ending.By this much stronger thread rolled ending, the shock shaft is virtualy unbreakable.The shock rod-end that fits to this piston rod is partno: 50320-41 and 50320-42
Piston rod fits in shock absorber: 50320 and 70300
Op voorraad
Referentie: 70524 B4
Spring Spline Drive (2pcs)
Spring set for the spline drive.
Assures correct positioning of the drive shafts and dif shafts.
Op voorraad
Referentie: 70300-30red
PROGRESSIVE SPRINGS 110MM RED
Progressive coloured springs for the by-pass shocks, (fits also Losi shocks)
Length: 110mm (with thread diameter 2.6mm)
Internal diameter: 32mm
Sold als pair.
Op voorraad
Referentie: 80414 F2
Steering plate
Steering plate incl. all needed asembly materials and bushing and bearings.
Op voorraad
Referentie: 51105 B1
Down stop plates from steel (4pc.)
Steel down stop plates for the chassis
Op voorraad
Referentie: 18410-09
Low Nut M8x1
Low nut (Metric fine), used for pressure adjustment of the servo saver spring
Op voorraad
Referentie: 45900-09 C4
Rubber membrane - mark II
Rubber membrane for the air brake - mark II.
Op voorraad
Referentie: 80605 F1A
Housing clutch bell
Housing for the clutch bell.
Machined from high grade 7075 alloy.
Op voorraad
Referentie: 50750-04 G3
Teflon tube exhaust
For the connection of the manifold and exhaust
Op voorraad
Referentie: 70300-04 A2
By-Pass shocker housing (front)
By-Pass shocker housing for the front shocker
Op voorraad
Op voorraad
Referentie: 80416 F2
Steering lever R
Steering lever for mounting the steering plate and steering rods.
Op voorraad
Referentie: 80509 F4
Upper arm rear
Rear upper arm made of high grade 7075 alloy.
Op voorraad
Referentie: 80505 F4
PINION CARRIER
Pinion carrier, used on the rear and front of the Fourtex.
Op voorraad
Referentie: 80110
body Fourtex
Body for the FourteX.
Delivered as clear shell.
No decals, paint or masking tape included.
Op voorraad
Bushing with conical collar for the servo saver.
Inside Ø3mm
Outside Ø4mm
Fits ball joint (50320-20) which has a hole of Ø4mm