Referentie: 80701 F3
Motor mount small
Small motor mount made from high grade alloy 7075.
Op voorraad
- Er zijn geen items meer in uw wagen
- Verzending
- Totaal € 0,00
- 1:10 Scale
- 1:6 Scale
- 1:8 Scale
- BBB-P Shocks
- Downloads
- Electronics
- Materials
- Silicone Oil
- Tools
Ring for Spline Drive
Waardering
Ring for the spline drive to secure the pin.
Made from alloy, anodized and laser engraved with Elcon logo.
Productdetails
70528 B4
4 Items
Recensies
Geen klantenbeoordelingen op het moment.
16 andere producten in dezelfde categorie:
Referentie: 70320-041
+10MM BY-PASS SHOCKER HOUSING REAR
By-Pass shocker housing of the rear shocker
Op voorraad
Referentie: 70413-02 C1
Disc for pivot C-hub
Disc for the pivot of the C-hub, which is mounted on top and under the C-hub for a smooth steering of the front upright
Op voorraad
Referentie: 80612 F2
Support planet gear, front
Support planet gear, front side.
Made from high grade alloy 7075.
Op voorraad
Op voorraad
Referentie: 70300-30bleu
PROGRESSIVE SPRINGS 110MM BLEU
Progressive coloured springs for the by-pass shocks, (fits also Losi and bbb-p shocks)
Length: 110mm (with thread diameter 2.3mm)
Internal diameter: 32mm
Sold als pair.
Op voorraad
Referentie: 80605 F1A
Housing clutch bell
Housing for the clutch bell.
Machined from high grade 7075 alloy.
Op voorraad
Referentie: 50445-06 B2
Bushing with conical collar (Ø3mm/Ø4mm)
Bushing with conical collar for the servo saver.
Inside Ø3mm
Outside Ø4mm
Fits ball joint (50320-20) which has a hole of Ø4mm
Op voorraad
Op voorraad
Referentie: evo-023 C3
Stainless steel ball head m4
Stainless steel ball head with m4 right wire and a 4 mm hole for the serosaver to the servo
Op voorraad
Referentie: 80506 F3
Support rear, right
Support for the rear end of the FourteX, right side.
Op voorraad
Referentie: 980070
Radio box (EM)
Solid Elcon Models radio box.
The lid has a groove in which the extra edge of the box fits, This secures a tight fit and makes the radio box watertight. Comes with a silicone wire to make the lid water tight and a rubber grommet for the servo cables. The needed hole for the grommet is to be drilled by the customer on his personal prefered position
Op voorraad
Referentie: 80110
Chassis Fourtex (shorter wheelbase)
Chassis for the Fourtex for wheelbase according EFRA regulations.
Not including shorter drive shaft.
The chassis length is reduced at the front.
When using the front air brake it is needed to also replace the servo mounts and use small steering servos.
Op voorraad
Referentie: 80417 F2
Steering lever L
Steering lever for mounting the steering plate and steering rods.
Op voorraad
Referentie: 80608 F4
Ring gear (60T)
Ring gear with inner teeth (60T) for the planetary gears
Op voorraad
Referentie: 80507 F3
Support rear, left
Support for the rear left of the FourteX.
Op voorraad
Ring for the spline drive to secure the pin.
Made from alloy, anodized and laser engraved with Elcon logo.