Referentie: 45106-01 D1
ALLOY SERVO ADAPTER - ANGLED
Adapter angled foot to mount small servo's in the TraxX.
Op voorraad
- Er zijn geen items meer in uw wagen
- Verzending
- Totaal € 0,00
Rings for engine
Waardering
Needed as shim rings when engine is in layed down configuration.
Omschrijving
45130
Productdetails
45130 D1
1 Item
Recensies
Geen klantenbeoordelingen op het moment.
16 andere producten in dezelfde categorie:
Referentie: 45550-08 D1
Brake pads (set)
Set of brake pads for the TRAXX. The set consists of a 2mm thick and 3mm thick brake pad. Mount the thickest brake pad at the brake axle (inside).
Op voorraad
Referentie: 45506 D2
Wishbone rear L/R
Rear wishbone for the TRAXX & FourteX. Fits both left/right side of the car. Made from robust 7075 alloy. Incl. bushings and adjustment bolt
Op voorraad
Referentie: 45401 C2
Wishbone front
Wishbone for the front of the TRAXX. Fits both left and right. Made of high quality alloy
Op voorraad
Referentie: 45411 C2
C-hub (left/right)
C-hub for the TRAXX. Fits both left and right
Op voorraad
Referentie: 45500-02
Dif half (o-ring side)
Differential half, o-ring side. Contains only the bronze bushing pressed in the difhalf for the outgoing difcup. (Not included: difcup, bearings, oil seal etc)
Op voorraad
Referentie: 45608 D1
Support clutch bell
Support of the clutchbell of the TRAXX. Includes bearing, shims and needed assembly materials.
Op voorraad
Referentie: 45412 C1
Upright L/R
Front upright for the TRAXX. Fits both left and right side. With hexagon adaptor for the new air brake series.
Op voorraad
Referentie: 50445-06 B2
Bushing with conical collar (Ø3mm/Ø4mm)
Bushing with conical collar for the servo saver. Inside Ø3mm Outside Ø4mm Fits ball joint (50320-20) which has a hole of Ø4mm
Op voorraad
Referentie: 45417 C3
Slave axle steersysteem
Slave axle for steeringsystem of the TRAXX.
Op voorraad
Referentie: 70512-1 D3
3 DEGREE TOE INSERT TRAXX 2.0 / GUNN EDITION
TRAXX 2.0 & Gunn Edition FourteX. Can be mounted left and right adjustment in wheel base possible The upright slots into the insert for a rock solid mounting Made from robust 7075 alloy. Incl:plastic bushing / screws
Op voorraad
Referentie: 70524 B4
Spring Spline Drive (2pcs)
Spring set for the spline drive. Assures correct positioning of the drive shafts and dif shafts.
Op voorraad
Referentie: 45415-06 C3
Steering rod (SS), L-105mm
Steering rod made from stainless steel. (L=105mm)
Op voorraad
Referentie: 70509 D3
PINS UPRIGHT, FRONT & REAR (SET)
Pin set (stainless steel) for mounting the upright / c-hub on the front- and the rear wishbone. The pin is mounted with 2 nyloc nuts and rings.
Op voorraad
Referentie: 70532 B4
CENTER PINS SPLINE-DRIVE (SET)
Center pin for the Spline-Drive. It is recommended to replace both parts Delivered as set.
Op voorraad
Referentie: samba-s
SAMBA PIPE FOR STANDING ENGINE
Samba exhaust for the Traxx Including all assembly materials. For standing engine.
Op voorraad
Needed as shim rings when engine is in layed down configuration.