Op voorraad
- Er zijn geen items meer in uw wagen
- Verzending
- Totaal € 0,00
- 1:10 Scale
- 1:6 Scale
- 1:8 Scale
- BBB-P Shocks
- Downloads
- ELCON
- ELCON
- Electronics
- Materials
- Silicone Oil
- Tools
Lay shaft
Waardering
Lay shaft for the TRAXX.
Including shims.
Omschrijving
45607
Productdetails
45607 amt
1 Item
Recensies
Geen klantenbeoordelingen op het moment.
16 andere producten in dezelfde categorie:
Referentie: 45620
Teflon clutch - 6 shoe
High-end 6-shoe teflon clutch, fits TraxX, Imp4ct and FG & HPI models.The engagement point is fully adjustable over the setscrews.
The clutch will tighten itself onto the crankshaft cone, by rotation of the crankshaft.
The clutch can easily be removed using a M8 bolt.
The clutch must be assembled by the buyer
Op voorraad
Op voorraad
Referentie: 70524 B4
Spring Spline Drive (2pcs)
Spring set for the spline drive.
Assures correct positioning of the drive shafts and dif shafts.
Op voorraad
Referentie: 70521 B4
Drive shaft for Spline-Drive (set)
Drive shaft for the Spline-Drive.
Delivered as set.
Op voorraad
Referentie: 45751
Exhaust TRAXX complete - lay down engine
High power exhaust for the horizontal / lay down engine.
Complete including manifold.
Op voorraad
Referentie: 18701 A2
Bolt for shocker (aloy whishbones)
Bolt for mounting the shock absorber onto the aloy lower wishbones.
Op voorraad
Referentie: 50900-08 A2
Wheel hex/square (set)
Wheel hex/square for the air brake.Hard anodized aluminium.Assembling materials included.
Op voorraad
Referentie: 45520 amt
Shocktower extension
Adjustable shockertower extension.
Makes your shocktower wider allowing a more vertical position of your rear shocks. This add lateral grip especialy on sand and cley tracks.
Beside a wider position height can be adjusted as well in 3 positions for optimal use of small/big wheels.
Op voorraad
Referentie: 45411 vt
C-hub (left/right)
C-hub for the TRAXX.
Fits both left and right
Op voorraad
Op voorraad
Referentie: 45500-03
Dif half (gear side)
Differential half, gear side.
Contains only the bronze bushing pressed in the difhalf for the outgoing difcup.
(Not included: difcup, bearings, oil seal etc)
Op voorraad
Referentie: 50445-06 A2
Bushing with conical collar (Ø3mm/Ø4mm)
Bushing with conical collar for the servo saver.
Inside Ø3mm
Outside Ø4mm
Fits ball joint (50320-20) which has a hole of Ø4mm
Op voorraad
Referentie: 70509 A2
PINS UPRIGHT, REAR (SET) For Traxx And F/R For Fourtex
Pin set (stainless steel) for mounting the upright / c-hub on the front- and the rear wishbone.
The pin is mounted with 2 nyloc nuts and rings.
Op voorraad
Referentie: 45407 vt
Topdeck
Topdeck for the TRAXX.
Delivered included assembly materials.
Op voorraad
Referentie: 70541
SPLINE DRIVES - COMPLETE SET
Complete set of spline drives shafts .
2CC of grease for the spline and 2CC of oil for lubrication of the CVD is delivered in the package.
Wheel squares are not included.
Op voorraad
Lay shaft for the TRAXX.
Including shims.